Simple Bookcase Plans
Simple bookcase plans is bookmark about Bookcase bookmarked by dale with ID 1611037273 was uploaded on 01-01-2019 and has been viewed 263,091 times.
OverviewHere's a simple DIY bookshelf project that gives you a chance to pass some of your woodworking skills on to the next generation.Any kid will love spending the day with you assembling this bookcase.
And by the end of the day, your helper will have hands-on experience with several power tools, plus an attractive homemade bookshelf to show off.The knotty pine bookcase parts are all standard dimensional lumber that you can find at any home center.
We joined the shelves and legs with biscuits.If you don't own a biscuit joiner but still want to build this project, you can simply nail or scr*w the parts together and fill the holes.We used a table saw to cut the 1-1/2-in.
square legs from 2x4s and a router with a 45-degree chamfer bit to bevel the edge of the top.If you don't have a table saw or router, you can just use stock 2x2s for the legs and leave the edge of the top square.
Meet Justin and JacksonWe recruited Justin and his son to help us with this homemade bookshelf story.Justin is a full-time firefighter and a woodworker on his off days.His 11-year-old son Jackson, an up-and-coming woodworker, had fun with his dad and learned a few power tool techniques in the process.
We provided the plans and gave a few pointers along the way, and Justin and Jackson took it from there.Getting started: Build a DIY BookshelfUse the Cutting List (see Additional Information, below) as a guide for cutting all the parts.
The next step is to mark the shelf positions on the shelf sides.It's important to keep track of the orientation of the parts.For reference, we placed a piece of masking tape on the top of each side, and on the top side of each shelf.
Justin and Jackson used a framing square to draw lines indicating the bottom of each shelf (Photo 1).No need to mark the location of biscuits on the shelves and sides.Instead make marks on the scrap of wood used as a fence.
Draw marks to indicate the outside edges of the 1x8 shelves and sides, and mark 1-3/4 in.in from each edge to indicate the center of the biscuits.To use the fence, line up the outside marks with the edges of the part you're cutting slots in.
And then line up the center mark on the biscuit-joining tool with the marks for the center of the biscuits (Photos 3 and 4).To mark the legs and sides for biscuits, set the legs in position and make pairs of marks that line up with each other on the legs and sides (Photo 2).
Put a piece of masking tape on the top of each 2x2 leg, and keep this facing up when you cut the biscuit slots.Photo 7 shows how to bevel the legs.Cut slots for the biscuitsBiscuit joiners have a flip-down fence that can be used to position the slots, but instead we're showing a method that allows you to reference the slots from the base of the biscuit joiner.
Photos 3 - 6 show the techniques.For a more detailed description of this method, see 'Building Cabinets With Biscuit Joints' .Jackson didn't have any trouble mastering the biscuit joiner.With a little coaching from Justin, he cut slots like a pro.
What's trickiest about cutting the slots is keeping track of the orientation of the parts.Just remember to keep the masking tape facing up, with one exception: The slots on the 1x8 top should be cut with the tape side down.
Glue the bookcase togetherHere's where a helper like Jackson really comes in handy.You have to work fast to spread the glue in the biscuit slots and onto the biscuits (Photo 8), and then assemble the parts before the glue starts to swell the biscuits (Photo 9).
Start by arranging all the parts on your work surface.Justin used a flux brush to spread the glue in the slots, and onto the biscuits after they were installed.Any small brush will work, though.When you have everything assembled, install clamps to hold the sides tight to the shelves while the glue dries.
Check by using a framing square or by measuring diagonally from opposite corners to make sure the bookcase is square.Adjust it if needed.Then tighten the clamps.This is a good time to take a break while you let the glue dry for about an hour.
Build the topTo minimize potential cupping, we decided to make the top by gluing two pieces of 1x6 together rather than using a solid board.Choose a straight piece of 1x6 with a sharp, clean edge.Cut the pieces long and trim the top to length after you glue the two parts together.
For pro tips on gluing boards edge-to-edge, see 'Edge Gluing Boards' .Justin and Jackson cut biscuit slots in the sides of the two 1x6s to help hold them in alignment while installing the clamps.Glue and clamp the two 1x6s.
Then let the glue set up about 30 minutes before routing the edge (Photo 10).Add the legs, top and backThe legs are held to the sides of the bookcase with biscuits.When attached, the legs should protrude 1/2 in.
past the outside, and overlap the shelves by 1/4 in.Glue in the biscuits, spread a line of glue along the edge of the side, and clamp the legs to the sides (Photo 11).Let the glue set for about 30 minutes.
Drill four 3/8-in.holes at the corners of the bookcase top.The holes are oversized to allow the top to expand and contract.Attach the top with four 1-1/4-in.screws and 1/4-in.washers.Complete the bookcase by scr*w*ng the four 1x6s to the back of the unit (Photo 12).
Drill 1/8-in.pilot holes for the screws to avoid splitting.A little final sanding and the bookcase was ready for finish.When we left them, Justin and Jackson were discussing finishing options but were leaning toward a wipe-on oil finish.
Our build-it-together bookcase was a great success—give it a go with your up-and-coming woodworker.Project PlansCutting ListMark both sides at onceTo start this easy DIY bookshelf project, first lay the bookcase sides together to mark the shelf locations.
The layout marks have to be perfect, so Justin closely supervised this step.Mark the biscuit slotsMake pairs of corresponding marks on the legs and sides.Later you'll center the biscuit joiner on the marks to cut slots that align.
Slot the end of the sideClamp the fence to the work surface and b*tt the end of the shelf to it.Then center the biscuit joiner on the mark and cut the slot.Repeat for the second slot.Cut slots for the shelvesLine up the 2x2 jig with the edge of board mark and clamp it.
Center the biscuit joiner on the center mark on the fence and cut the slot.Repeat for the second slot.Cut slots for the legsLine up the center of the biscuit joiner with the marks on the edge of the side and cut the slots.
Make sure both the shelf side and the biscuit joiner are tight to the work surface when you cut the slot.Position the slot with a spacerPlace a scrap of 1/2-in.plywood or particleboard on the work surface.
Butt the leg against it and rest the biscuit joiner on the spacer while you cut the slots.The 1/2-in.spacer will automatically position the slots.Bevel the legs with a simple jigScrew two scraps to a small square of plywood to form a cradle for the legs.
Clamp the jig to the miter saw fence, and cut a 10-degree bevel on the bottom of each leg.Add the biscuitsWork quickly to glue biscuits into the slots.Spread the glue in the slots, and onto the biscuits, with a brush.
Assemble the shelves quicklyBiscuits start to swell and lock in place soon after the glue is applied, so it's important to get the shelves assembled quickly.Beveling the edge is a job for DadUse a router and a 45-degree chamfering bit to bevel the front and sides of the top.
Jackson held the top to keep it from shifting on the Bench Cookies (available at rockler.com).Insert the biscuits and clamp the legsSpread the glue and insert the biscuits.Then glue on the legs.Clamp them and wait for the glue to dry before moving on to install the top and back.
Screw on the back boardsDrill pilot holes to prevent splitting.Then scr*w the boards to the back of the bookcase.With a little coaching, Jackson was driving screws like a pro...